Acessories for Thermocable®

A1333-COJ Power and end termination kit for THERMOCABLE®.
S1334-COJ In-Line splice kit for THERMOCABLE®.
E1336-COJ Three-pack end termination kit for THERMOCABLE®.
PFK-1 Power feed kit: to connect one or two THERMOCABLE® and temperature sensor(s) on a pipe to an electronic thermostat.
PFK-4 Power feed kit: to connect one THERMOCABLE® and temperature sensor(s) on a service pipe to an electronic thermostat.
PFK-custom Custom power feed kit: on request, to suit the application, to connect one or two THERMOCABLE® and temperature sensor(s) from one or two locations to an electronic thermostat.
A-300 Aluminum foil tape roll 50 mm (2 in) wide x 45 m (150 ft) long.
URTD-06-R or G 100 ohms temperature sensor with 6 m (20 ft) PVC lead wire (in red or grey).
URTD-15-R or G 100 ohms temperature sensor with 15 m (50 ft) PVC lead wire (in red or grey).
URTD-30-R or G 100 ohms temperature sensor with 30 m (100 ft) PVC lead wire (in red or grey).

Note: Only Urecon electrical accessories such as power termination, end termination and splice are certified for use with THERMOCABLE®.

A1333-COJ Power end/termination kit:

Contains one power end connector with two bushings, one heat shrinkable end cap, one heat shrink tube, one roll of Teflon® tape, butt splice connectors and ground wires. Used for the connection of one THERMOCABLE® to a thermostat or junction box.

A1333-COJ Power end/termination kit

S1334-COJ Splice kit:

Contains all necessary material to splice two THERMOCABLE® together.

S1334-COJ Splice kit

E1336-COJ Three pack, end termination kit:

Contains three heat shrinkable end caps, three heat shrink tubes and one roll of Teflon® tape. Used for the end termination of three THERMOCABLE®, often used to seal cables for future connection at vacant building lots, etc.

E1336-COJ Three pack, end termination kit

PFK-1 Power feed kit:

Contains all the necessary material to bring power from an electronic thermostat to two
# 12 AWG bus wire THERMOCABLE® on a pre-insulated pipe; power leads, splices, end caps and 2 x 6 m (20 ft) of flexible metallic conduit to protect the power leads and temperature sensor wiring (not included).

PFK-1 Power feed kit

PFK-4 Power feed kit:

Contains 2 x 3 m (10 ft) of flexible metallic conduit to protect the THERMOCABLE® and temperature sensor wiring (not included) from an electronic thermostat to the pre-insulated pipe. Includes a heat shrinkable tube and end cap.

PFK-4 Power feed kit

PFK-Custom Power feed kit:

A custom power feed kit is required when two controlling (pipe) temperature sensors are to be installed on a given pre-insulated pipe. As specified by the customer, it would contain the material required to bring power from an electronic thermostat to one or two THERMOCABLE® on a pre-insulated pipe. This could include; power leads, splices, end caps, one length of flexible metallic conduit to protect the power leads and two lengths of flexible metallic conduit to protect the temperature sensor wiring (not included). Each conduit length has to be specified.

PFK-Custom Power feed kit

URTD Temperature sensor:

100 ohms RTD temperature sensor for use with the UTC line of electronic thermostats. Available with 6 m (20 ft), 15 m (50 ft) or 30 m (100 ft) of grey or red PVC extension lead wire for ease of identification.

URTD Temperature sensor

A-300 Aluminum foil tape:

50 mm (2 in) wide x 45 m (150 ft) long roll of aluminum foil adhesive tape. Used to tape the temperature sensor(s) in place to enhance temperature transfer and to secure THERMOCABLE® at connection points, valves, etc.